From SCUD to SMOKO: Ben Simpson’s 1200hp XY is ready to make some noise

Ben 'Scud' Simpson is back and ready to rock at the Castlemaine Rod Shop Invitational

Share

After years of making a name for himself with wild Datsun burnout cars, Ben Simpson has gone in a very different direction. His latest project is a heavily modified 1970 XY GTHO, packing a blown big-block Chev, more than 1200hp and a whole lot of experience behind it.

If you’ve followed the Australian burnout scene over the years, chances are you’ve come across Ben Simpson.

He’s the bloke behind SCUD, the silver V8-powered Datsun 1200 that has caused plenty of chaos over the years, including that now-infamous rooftop skid on Darwin’s Evolution Tower. There’s also CHEESE, the little Datsun that had firefighters working overtime at Tread Cemetery and was later given a makeover as MINION.

But after spending so many years building and competing with small cars, Ben has decided it’s time for something a little different.

Meet SMOKO: It’s a 1970 Ford XY Falcon, and it’s about as far removed from his old Datsuns as you could get. Finished in bright yellow metallic paint, the big Ford has been built from the ground up as a dedicated burnout car, with a full tube chassis, a heavily modified interior and a big-block Chev sitting between the rails.

Ben picked up two XYs around five years ago and spent some time deciding which one would become his next project. The car he eventually chose had previously been used for drag racing and came with some existing chassis work, but it wasn’t up to the standard he wanted. So he stripped it back and started again.

What followed was around four years of work, with Ben fitting the build in around racing, travelling to events and the usual costs that come with running burnout cars. He’s had plenty of experience over the years, but this time he wanted to put everything he’d learnt into one final big project.

“I’ve probably had over a hundred cars in my lifetime, all different variants,” he says. “And yeah, I’ll just go all out with this one and put in everything I’ve learned over the years.”

The XY is essentially a body shell wrapped around a purpose-built competition car. Ben built the main chassis rails and rear clip to carry the four-link suspension and Ford nine-inch differential, while the front end uses heavily modified Nissan components, adjustable struts and K-Lock drift steering to give him the angle needed on the pad. There’s custom metalwork throughout, including a floor built from scratch, a modified interior, a custom dash and a full tube chassis.

Ben has also fitted a Haltech management system with data logging, allowing him to keep an eye on temperatures, exhaust readings and other information while the car is running. It’s a long way from simply dropping a big motor into an old streeter: “It’s a skin of a car,” he says. “All the rest inside I built.”

The engine package came about through a conversation with Brett Nidre at BNR Engines, someone Ben has known for more than 20 years.

Rather than chasing a particular brand or building something just for the sake of it, Ben wanted a reliable combination that would do the job. He asked Brett what he had available, and the big-block Chev package was the one that made sense.

The result is a 502-cube big-block Chev topped with a 10/71 supercharger and an Enderle Barndoor hat, running on methanol and backed by a two-speed Powerglide.

“Brett said a soft tune should be about 1200hp,” Ben says. “We could wind it up if we want to, but I’m sure that’s enough.”

The driveline is just as serious, with a full-floating 35-spline nine-inch differential and 3.0:1 gears. And after years of working out what breaks, what works and what needs to be stronger, he’s hoping this combination will give him a dependable package. There have already been a few testing sessions, including a run at the South East Skid Fest event in Millicent where Ben was able to put the car through its paces before breaking an input shaft in the gearbox. It wasn’t exactly the test result he wanted, but that’s what testing is for.

He replaced the shaft and has since been back out for more shakedown work, with the latest session going much more smoothly. So far, he’s only had a couple of proper opportunities to drive the XY, along with some testing on a mate’s 10-acre property. He’s keen to get more seat time and find out how the car behaves on a bigger pad.

That’s one of the biggest differences between SMOKO and his previous cars. Ben knows how SCUD and Minion behave, but every car has its own personality, and this one has a lot more horsepower and a very different footprint.

“Every car’s different. They all move around different,” he says.

He’s also looking forward to taking it to events where he can do more than just burnouts. With a set of sticky tyres ready to go, Ben wants to try some off-street racing and power skids as well, getting a feel for the car in different situations.

The next few years are likely to involve plenty of travelling, too. Ben has spent a lot of time around the country over the years, including helping run Brashernats in Darwin with Mick Brasher. He was also involved in getting the drag strip and burnout pad established there, with significant government funding going towards the facility.

He’s been to events all over Australia and reckons Perth is about the only major stop he hasn’t ticked off yet. With SMOKO finally coming together, that could change.

For now, though, the immediate focus is the Castlemaine Rod Shop Invitational 3. Ben contacted Heath Waddintgon to see whether there was a spot available, and after a couple of other entrants pulled out, he got the call.

After years of turning up with SCUD and his other Datsuns, it’ll be a change to roll in with a big yellow XY. And while he’s keen to put on a good display, Ben isn’t planning to destroy the car just to chase a result.

He knows there are some serious competitors in the field, and with the Invitational being a winner-takes-all deal, he expects the top cars to be pushed hard. His own priority is getting more time behind the wheel and making sure the new combination does what it’s supposed to.

There could be another little surprise for the crowd, too. During testing, the XY put on a bit of a flame show out of the exhaust. Ben initially thought it might have been a tyre fire, but after checking the footage and inspecting the car, he found it was simply fuel burning off through the exhaust.

The engine was running rich, and the flames were coming straight out of the back. He’s not sure whether it’ll happen again, but if SMOKO decides to put on a show after dark, it could make for some pretty entertaining viewing.

The car’s paint is another detail worth seeing in person. It’s not just a standard yellow, either, with a metallic flake running through it that really comes alive in the sunlight. Ben says a few people have already seen photos online, then turned up in person and commented that the pictures don’t do it justice. The paintwork was handled by Craigieburn Crash, while Brett Nidre and the team at BNR Engines took care of the engine package.

For Ben, though, the best part of having SMOKO finished is simply getting back out there. He’s spent four years building it, and now he’s ready to enjoy the next few years travelling to events, catching up with mates and finding out what the XY can do.

Comments